Lê Huy Lâm ( Mr )
[Sales engineer]
[Cellphone]: 0915.493.164 – 0915.031.817
[Email]: sale10@tmpvietnam.com
[Zalo]: 0163.2844.226
Measuring hardness with Durometer
1. In case of measuring by pushing by hand, putting pressurized surface of durometer held by hand from the top vertically with a certain speed to the flat face of work piece which is put on the flat face . Then, after adhering it, regard the value measured within the passed time prescribed by standard as “hardness”.
2. In case of measuring hardness by mounting durometer to stand, measuring speed (not more than 3.2mm/sec.), pressurized load (type A, E is 1kgf, type D is 5kgf) and pressurized surface diameter (φ18mm) of type A / D durometers including tolerance are standardized.
3. Measuring point of test piece is to be inside from its edge by 12mm or more and clearance is to be 6mm and more. Thickness is normally 6mm and more, and 10mm and more for type E.
4. Test environment : Temperature is 23℃±2, humidity is 50±5% and median or average is applied for measured value. If 50 show in type A case, it is described［A50］. These are ruled for each standard.
Hiện nay chúng tôi đang là nhà phân phối và đại lý của nhiều hãng lớn trên toàn thế giới với đầy đủ các trang thiết bị máy móc, quý khách có thể tham khảo thêm:
AT2E, As scholer, Ametek PI, Ametek test, Bircher, Barksdale, Beckhoff, Busmann, Baumuller, Baumer, Elau, Elettrotek Kabel, IBA, Kern Sohn, Keller, Kiepe, Mark 10, Matsushima, Matsui, Masibus, Maxonic, Mehrer, Nireco, Pilz, Pora, Pentair, Redlion, Rotork, Soldo, Teclock, TDK Lambda, Telco Sensors, Yokogawa, Wise, Wago, Wittenstein, Asa – RT, Aviteq, Bihl wiedemann, Brevini, Conatec, Gemu, Kyowa, Mdexx, Megatron, Meinsberg, Microsonic, Meinsberg, Microsonic, MKS Anlasser, Novotechnik, PMA, PS electric, Schiebel, Singerland Bremsen, Spohn Burkhardt, Sytstec, STI Vibration Monitoring, Tematec, Van Der Graaf, Vaccum Barrier,…
[Sales engineer]
[Cellphone]: 0915.493.164 – 0915.031.817
[Email]: sale10@tmpvietnam.com
[Zalo]: 0163.2844.226
Measuring hardness with Durometer
1. In case of measuring by pushing by hand, putting pressurized surface of durometer held by hand from the top vertically with a certain speed to the flat face of work piece which is put on the flat face . Then, after adhering it, regard the value measured within the passed time prescribed by standard as “hardness”.
2. In case of measuring hardness by mounting durometer to stand, measuring speed (not more than 3.2mm/sec.), pressurized load (type A, E is 1kgf, type D is 5kgf) and pressurized surface diameter (φ18mm) of type A / D durometers including tolerance are standardized.
3. Measuring point of test piece is to be inside from its edge by 12mm or more and clearance is to be 6mm and more. Thickness is normally 6mm and more, and 10mm and more for type E.
4. Test environment : Temperature is 23℃±2, humidity is 50±5% and median or average is applied for measured value. If 50 show in type A case, it is described［A50］. These are ruled for each standard.
Hiện nay chúng tôi đang là nhà phân phối và đại lý của nhiều hãng lớn trên toàn thế giới với đầy đủ các trang thiết bị máy móc, quý khách có thể tham khảo thêm:
AT2E, As scholer, Ametek PI, Ametek test, Bircher, Barksdale, Beckhoff, Busmann, Baumuller, Baumer, Elau, Elettrotek Kabel, IBA, Kern Sohn, Keller, Kiepe, Mark 10, Matsushima, Matsui, Masibus, Maxonic, Mehrer, Nireco, Pilz, Pora, Pentair, Redlion, Rotork, Soldo, Teclock, TDK Lambda, Telco Sensors, Yokogawa, Wise, Wago, Wittenstein, Asa – RT, Aviteq, Bihl wiedemann, Brevini, Conatec, Gemu, Kyowa, Mdexx, Megatron, Meinsberg, Microsonic, Meinsberg, Microsonic, MKS Anlasser, Novotechnik, PMA, PS electric, Schiebel, Singerland Bremsen, Spohn Burkhardt, Sytstec, STI Vibration Monitoring, Tematec, Van Der Graaf, Vaccum Barrier,…
Nhận xét
Đăng nhận xét